Відео

Was able to tackle this using a small flathead screwdriver and some patience to get them straightened out. It might not be perfect but it's much better than it was. Thanks for the tip!

Thank you so much for this video. It's so helpful. My ac is a wall unit. I'm wondering how to drain the water that got in from my spraying. I don't see a drain hole.

The rod is not to check if it's balanced. It is to check if the blade is bent.

I have three window A/C units I've collected over the years; some were purchased, some donated. Over the years each one of them has been removed from the window and placed on the lowered tailgate of my pick-up for disassembly and clean-up. Instead of store-bought expensive A/C cleaner I went with vinegar with a little bit of Dawn and baking soda. Spray down everything that's dirty, wipe down what you can (Q-tips are handy for those tiny, hard-to-reach areas) making sure to get all the black, brown and green spots...that's mold. That's what stinks. In Florida I let it set for about an hour to dry. Back in the window, back on high until it expires then off to Walmart for another.

Hello Sir i have a vt commodore and my steering wheel is shuddering when im on the brake , i took the front wheel of today and there was play from side to side but not.up.n down does that mean my wheel bearings are gone?

That's a great video. I like that tool better than the one that spins because you have to go back-and-forth with that one. This one you just hold the square in my mind squares up that wheel much better than going back-and-forth with that roller type dresser. Good job.

That thing is $60 now…after the rebate.

Use Red loctite if you don't have a lock nut

Perfect. Just what I needed to avoid any surprises. Screwdriver stuck down the holes to keep it from reeling out was key.

How do you clean the back part (where the water lands)? Mine keep getting pink slime, and I have to remove from the window and pressure wash, it's so much work. Can I spray bleach and water in there? Thank you

Everybody’s so proud that they got soaked for $100. 🤷‍♂️

I bought the same balancer on Amazon for $32. And why would you want to change out the magnets?

What if the tire moves in all directions including the strut tower

I have an iHeater and it is different from the heater you are demonstrating. I cannot figure out how to get the back off to get to the reset button or to the bulbs. Can you help? Thanks.

i have a brabd new 24k btu window unit. never been used. the display turns on but nothing else.

Thank you. This helped a lot. Trying to catch a possibly rabies infected animal. Appreciate it very much. This is the Lord's work you've done. I got bitten and I can't afford to have rabies shots. Plus I've had rabies shots before as a child and do not want to go through that again unless I have to.

Mine only cool on level 10 any suggestion

Thank you! I wanted to know about cleaning the outside. 🎉

Thank you!

No one shows how to adjust that metal arm there's two little tabs on that plastic vein

TRILLEEEER.

Many thx! Even I can clean mine. FYI: let all parts dry before plugging in. I hope you unplugged too! Thx for the links too.

I know the balancer operation is self explanatory, but wanted to see one in action b4 buying. Looking at the MaxPower one myself. Thanks 4 the video friend.... GO CATS! (noticed your shirt ;)

What is the model number of the window air conditioner in this video?

What if you change the uppers and lower already

Thanks!

My tire almost feel off while I was mowing didn’t know that’s all that holds them off to part store tomorrow Thanks for video

Both of these videos are Great!!! I really do miss that A villa track so much and wished it was still there!! I would go all of the time!!!!

MrJustDIY, Very helpful video! Thanks!! Can't wait to try mine. Paulie

Very informative information, ty

So mone wobble a bit left to right is that tie rods? Not a lot of play just a bit and nothing up an down

You're a kind person. Lots of shops wont work on this inexpensive stuff. Best wishes to you

Thanks for the video I will check mine out

Tucker Carlson is incredibly talented. Had no idea he was so handy

thank you that was a good lesson

That cleaner is nice.

I noticed that you didn't rinse the inside after spraying with the cleaning foam. A previous video i watched used a spray bottle of water to rinse. Does it matter? Thank you for this excellent, step-by-step, detailed video! Also for the links, which i WILL use!! 👍👍👍

plastic case for 200 dallor tap and die set.

Buddy, go buy life insurance, because no jack stands under that truck means no longevity for you.

Thank you

Why not a bad plug ?

EXACTLY what I needed to know. Well done. Excellent.

Thanks for making this nice and detailed.

Awesome Video...‼Thank you So Much‼

I have a bowtie hole blade on my honda will it work

What if you have the other type, I have already changed.

That's why you should save your money and buy a STIHL, Echo, Husqvarna, Shindaiwa, or a Redmax

Size?

Have you done any heavy threading and been able to tell if the tap threads are holding up? I've used several cheap sets and they thread the bolts sloppy and barely last a few taps. I'm hoping this one holds up because i thought abput buying it. I got a harbor frieght set and returned it th3 same day it was so cheap and bad.

That's not fair at all. Walmart is the only main company that sells hypertough branded tools, so the life warranty for exchange only has to be covered by them with or without a receipt. You will have to be very clear and on point with the walmart customer service staff cuz most of them dont know their warranty rules and dont know how to do their job.